We accept Visa and MasterCard
Pay by Direct Credit (NZ only)

Products List


Home » Reloading Stuff + » Case Prep Tools




  • 338cal Neck turning Mandrel
  • For use with Hornady Neck Turning Tool
List Price: $21.95
Price: $19.95
17.96 AUD
Add to cart

Bench Source Brass Case Annealing Machine Gas


  • Many times, brass necks or shoulders will split from too many reloadings or cartridge cases will work harden and be discarded that seemingly no longer shoot accurately.
  • When annealed properly, your brass will have a longer life and display less fliers on the target. And at an average of 400-500 per hour, it won’t take up too much valuable time that you could be out burning powder! 
  • 110 volt with a 220 volt switch. Torch heads are pictured, but not included.
List Price: $1,199.95
Price: $1,160.00
1,044.00 AUD
Out of Stock

Dillon D.C.L. Case Lube 5000


  • Dillon Case Lube (D.C.L.) 5000
  • Environmentally Safe
  • Pump Bottle (Non Aerosol)
  • Qty 8oz
  • Dillon Part #13733
List Price: $29.95
Price: $24.95
22.46 AUD
Add to cart

Forster 3-in-1 Case Mouth Cutter


  • Forster 3-in-1 Case Mouth Cutter
  • Achieve 3 Jobs at the Same Time
  • Trim Case length
  • Chamfer & Deburr Inside (14 deg) & Outside (30 deg) Case Neck
  • Long Lasting Carbide Blades
  • Fits Forster Original or Power Trimmers
  • Save Time, Improve Consistency
  • Includes Pilot
  • Made in USA

List Price: $169.95
Price: $144.95
130.46 AUD
Add to cart

Forster Deburring Tool Base with Crank Handle


  • Use With Forster Inside/Outside Case Deburring Tool
  • Mount to Bench Top or Ply Wood & Clamp to Bench
  • Speeds Up Deburring
  • Made in USA
List Price: $69.95
Price: $59.95
53.96 AUD
Add to cart

Forster Hand Held Outside Neck Turner Pilot


  • Forster Hand Held Outside Neck Turner Pilot
  • Use with Forster  Hand Held Outside Neck Turner (HOT100)
  • Made in USA
List Price: $34.95
Price: $29.95
26.96 AUD
Add to cart

Forster Inside Neck Reamer


  • Forster Inside Neck Reamer
  • Mount in the Cutter of Forster Trimmer
  • Made from High Grade, Wear Resistant  Tool Steel
  • Staggered Teeth Cut Brass Smoothly

Three important notes about using your Forster Neck Reamer:

Neck reaming should only be performed after the cases have been fired with a full load and before the neck or full length sizing operation. Wall thickness can be measured with a tubing micrometer, but a simpler test for excess brass in the neck area is to slide a bullet into a fired, unsized case neck. If you feel interference, the neck should be reamed or outside neck turned.
Use neck reamers before resizing. Three exceptions to this rule are:
P/N NR1220-.220Å" diameter reamer for .224Å" bullets
P/N NR1239-.239Å" diameter reamer for .243Å" bullets
P/N NR4275-.4275Å" diameter reamer for .429Å" bullet
These are common sizes that reloaders use to ream their cases just before seating bullets. These three sizes are kept in stock for those who intend to ream after the sizing operation just before seating bullets.
We grind many other special sizes as needed. Wildcatters often require specially sized reamers when converting brass from one caliber to another. You tell us the size you need and we'll grind it to your exact specifications. A nominal special grinding fee applies. Our quick turnaround service adds a versatile case preparation tool to your Forster Case Trimmer System.

List Price: $59.95
Price: $52.95
47.66 AUD
Add to cart

Frankford Arsenal Case Neck Lubricator


Function: Lubricate case necks 
Material: Comes with Nylon Brushes and Motor Mica 
Includes: 1/10 oz packet of Mica, Hard plastic dust cover, mounting screws, 22, 24, 27, 30, 35 and 45 caliber brushes.  
Notes: Mica is only suitable for lubricating the case mount and is not suitable and CANNOT be used as a full length sizing lubricant 
List Price: $30.95
Price: $29.95
26.96 AUD
Out of Stock

« Previous | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10... | »

Website by Webfactor Limited, Dunedin, N.Z.